- What are the three main reasons for slips trips and falls?
- What is a tripping hazard?
- How high is a tripping hazard?
- Which of the following must be done to control slipping and tripping hazards?
- What are the 3 types of falls?
- Is slip trip and fall a hazard?
- How can we avoid tripping hazards?
- What are two common tripping hazards in a shop environment?
- What is the correct way to fall?
- How do you fix trip hazards?
- What is the most common contributing factor for tripping?
- What are 3 things you can do to help prevent slips?
- What are three examples of something a worker might slip or trip on?
- Why am I falling down a lot?
- What’s the most common type of injury caused by slips and trips?
What are the three main reasons for slips trips and falls?
What are the main causes of slips, trips, and falls?Uneven floor surfaces.Unsuitable floor coverings.Wet/slippery floors.Changes in levels.Trailing cables.Poor lighting.Poor housekeeping..
What is a tripping hazard?
Trip Hazard. Definition: Hazard caused by an abrupt change in vertical elevation or horizontal separation on any walking. surface along the normal path of travel.
How high is a tripping hazard?
1/4 inchThe Americans with Disabilities Act (ADA) of 1990 defines a ‘trip hazard’ as any vertical change of over 1/4 inch or more at any joint or crack. Since the ADA demands strict compliance, trip hazards represent a legal liability to our clients.
Which of the following must be done to control slipping and tripping hazards?
To help prevent slips and trips, CCOHS recommends the following: Clean up spills immediately. If a spill can’t be cleaned up right away, place “wet floor” warning signs for workers. Keeps walkways and hallways free of debris, clutter and obstacles.
What are the 3 types of falls?
Falls can be categorized into three types: falls on a single level, falls to a lower level, and swing falls.
Is slip trip and fall a hazard?
Slips, trips and falls on the same level are serious and account for about one fifth of all notified accidents. Many of these slips, trips and falls lead to serious injuries, with one in four resulting in an absence of over one month.
How can we avoid tripping hazards?
You can reduce the risk of tripping by:keeping walking areas clear from clutter or obstructions.keeping flooring in good condition.always using installed light sources that provide sufficient light for your tasks.using a flashlight if you enter a dark room where there is no light.More items…
What are two common tripping hazards in a shop environment?
Supplies, clutter and loose cords are two common tripping hazards in a shop environment. Tripping hazards refer to any sort of object that causes a person to slip, trip and fall. Loose cords refer to wires coming out from here and there that causes a person to trip over.
What is the correct way to fall?
There are correct ways to fall, however, the recommended procedures are:Tuck your chin in, turn your head, and throw an arm up. It is better-to land on your arm than on your head.While falling, twist or roll your body to the side. … Keep your wrists, elbows and knees bent.
How do you fix trip hazards?
There are two ways to fix sidewalk trip hazards:Completely dig out the peaked slabs and add new concrete. The entire effected area is removed to bare ground, surface is leveled and new concrete slabs are poured. … Use a Scarifier to level the slabs without removal.
What is the most common contributing factor for tripping?
Research tells us that many slips, trips, and falls are caused by circumstances that we can all do something about. The most common contributing factors to a slip, trip or fall are: rushing, frustration, fatigue, and being on autopilot.
What are 3 things you can do to help prevent slips?
Here are 10 ways you can prevent slips, trips, and falls around the workplace:Keep walking surfaces clean and free of clutter. By keeping walkways clear, you can quickly reduce the potential for injury. … Stairways & Handrails. … Manage cords. … Footwear. … Lighting. … Signage. … Step stools. … Check floor conditions, inside and out.More items…
What are three examples of something a worker might slip or trip on?
1. Common slip, trip and fall hazardspoor lighting.trailing cables.unsuitable floor coverings.uneven or damaged floor surfaces.contaminated floor surfaces, for example liquid or greasepoor housekeeping, for example tripping or falling over something left in a walk way.
Why am I falling down a lot?
This can be caused by dehydration, ageing circulation, medical conditions such as Parkinson’s disease and heart conditions and some medications used to treat high blood pressure. inner ear problems – such as labyrinthitis or benign paroxysmal positional vertigo (BPPV)
What’s the most common type of injury caused by slips and trips?
The most common injuries from these types of accidents, unsurprisingly, are fractures and dislocated joints.